Upgrade to remove ads
swjh CORE Introduction to Power Tools Review
Terms in this set (44)
An example of an AC power source is
a wall receptacle.
Before replacing parts such as bits, blades, or discs on any tool, you must
disconnect the power source.
On power tools you should never engage the
Drill bits are held in place by
drill chucks, which can be either keyed or keyless.
personal protective equipment, including appropriate eye, head, and hand protection.
To prevent electrical shock, power tools should only be operated with the proper
ground fault circuit interrupter (GCFI).
When using a power drill, proper ground fault protection will prevent
Keep the drill's air vent clean with a
small brush or small stick.
Most hammer drills will not hammer until you
put pressure on the drill bit.
Never use a circular saw unless the
lower blade guard is properly attached.
Saws with fine blades that are excellent for delicate and intricate cutting are called
The pneumatic drill is typically used
when there is no source of electricity.
Before you plug any saw into a power source, make sure the
work has been clamped down.
An abrasive cutoff saw is also referred to as a
chop saw or cut off saw.
A reciprocating saw, regardless of manufacturer, is often referred to as a
SawZall because it is one of the most popular brands on the market.
The power miter saw combines a miter box with a
circular saw, allowing it to make straight and miter cuts.
Before you start drilling make sure the drill bit is
tightened in the chuck.
Angle grinders (also called side grinders) are used to
grind away hard, heavy materials and to grind surfaces such as pipes, plates, or welds.
Bench grinders are
electrically powered stationary grinding machines.
The adjustable tool rest on a bench grinder should be
positioned 1/8 inch from the wheel.
The first step when using a pneumatically powered nailer for the first time is to
inspect the nailer for damage and loose connections.
Some manufacturers suggest that each time you use a pneumatic nailer, the air inlet needs
a few drops of oil.
If a pneumatic nailer is not firing properly, before you attempt repairs you must
disconnect the air hose.
Air impact wrenches are power tools used to
fasten, tighten, and loosen nuts and bolts.
When using an air wrench
keep your body stance balanced.
A Porta-Power is an example of a
When using a power nailer
never aim the nail gun toward your body or load the nailer with the compressor hose attached.
When finished making a cut with a circular saw
make sure the blade has stopped before setting the saw down.
A forstner bit is used on wood and is
particularly good for boring a flat bottom hole.
The better you use and maintain your tools,
the better you will be in your craft.
Before you begin setting up a pavement breaker for use, make sure that the air pressure is
shut off at the main air outlet.
Before you cut through a wall or partition
find out what is inside the wall and on the other side of the wall.
A detail grinder uses points
to smooth and polish intricate metallic work.
The electromagnetic drill is a
portable drill used on thick metal.
The end grinder is used to
smooth the inside of materials, such as pipe.
Hammer drills are designed to drill into
concrete, brick, and tile.
The high speed setting on a reciprocating saw is used for
sawing wood and other soft materials.
Hydraulic jacks are used when the application calls for
extreme force to be applied.
The most common use of the power drill is to
make holes in wood, metal, and plastic.
Pneumatic tools get their power from
Powder-actuated fastening systems are used to
anchor static loads to steel beams.
Use only a band saw that has a
When cutting with a circular saw, grip the
saw handles with two hands.
When using a saber saw, avoid vibration by
using a clamp or vise to hold the work.
THIS SET IS OFTEN IN FOLDERS WITH...
swjh CORE Introduction to Construction Drawings Re…
swjh CORE Introduction to Materials Hand…
swjh CORE Introduction to Hand Tools Ter…
swjh Class Rules
YOU MIGHT ALSO LIKE...
Monday Test 1 - Power tools
Monday Test 1 - Power tools
TOOL AND USE ID
Chapter 4 Power Tools
OTHER SETS BY THIS CREATOR
Electricity & Chemistry worksheet
Electricity - AC/DC, Cells, Batteries &…
6. Switches (A)
Electrical: Symbols and Schematics works…
OTHER QUIZLET SETS
Mod 4 Electricity I
#3 Ag Test