Upgrade to remove ads
Only $2.99/month

Pivot Point Chapter 9 Sculpture

Terms in this set (47)

The foundation for all other hair services is:
color
texture
sculpture
sculpture
The other boundary or silhouette of any shape or form is known as the:
structure
form line
structure graphic
form line
The term used to describe the hair as the lengths lay or fall naturally over the curve of the head is known as:
anatomy
natural fall
structure graphic
natural fall
The widest area around the head is known as the:
crest area
interior area
pairetal area
crest area
Which basic form consists of hair lengths that progress from shorter in teh exterior to longer in the interior and is referred to as a one lenth cut?
solid
gratuated
increased layered
solid
The graduated form is sometimes referred to as a wedge cut or an:
bob
shag
45 degree angle
45 degree angle
A layered cut or 90 degree cut is known as a:
solid form
graduated form
increase layered form
uniformly layered form
uniformly layered form
All of the following are true about the uniformly layered from EXCEPT:
a circular shape
activated texture
same lenth throughout
rectangular or oval shape
rectangular or oval shape
Which or the following scuplturing tools is used to create a clean blunt edge?
razor
shears
clippers
shears
When sculpting with a razor all of the following results are achieved EXCEPT:
ends are tapered
softer apperance to hair
regular alteration of short and long lenths
regular alteration of short and long lengths
Which finger should be place in the finger grip to control the still blade when holding shears?
ring
pinky
index
ring
The moveable blade of the shears is controlled by the
still blade
thumb grip
hand screw
thumb grip
To hold the comb and shears in the same hand without jeaprodizing the clients safety release the thumb grip and:
close your palm over the shears
close your fingers over the finger grip
wrap your thumb around the finger grip
close your palm over the shears
Taper shears also known as thinning shears are used on the hair to
reduce bulk
create precise lines
create a clean blunt edge
reduce bulk
Whenn using electric clippers the attachment that allows the hair to be sculptured at the same length is the
taper
razor
guard
guard
A trimmer also known as an edger is a tool used to
creat beveling
part and distribute the hair
outline and refine the hair
outline and refine the hair
As is sculpts the hair the moveable blade of the clippers moves
up and down
to the left only
from side to side
from side to side
Which tool controls short perimeter lengths when sculpting against the skin?
razor
trimmer
taper/ contour comb
taper/ contour comb
The term used to describe dividing the head into workable areas for the purpose of control is called:
designing
texturizing
sectioning
sectioning
The apex refers to what part of the head?
top
side
front
bottom
top
The area below the occipital is referred to as the:
nape
crest
crown
nape
What determines the size of the parting when sculpture hair?
color
density
texture
density
Which head position produces legnths that are shorter in the nape and longer surface lengths?creating an under bevel effect?
upright
tilted back
tilted forward
tilted forward
What type of distibution results in a 90 degree angle from its parting?
shifted
parallel
perpendicular
perpendicular
What term also known as elevation is the angle at which the hair is held in relation to the curve of the head prior to sculpting?
slithering
projection
texturizing
projection
Which of the following angles best represents low projection (elevation)?
0 degree to 30 degree
30 degree to 60 degree
0 degree to 30 degree
Angles between 60 degrees and 90 degrees represent:
no elevation
low elevation
high elevation
high elevation
Projecting the hair below 90 degrees would:
build weight
remove bulk
remove weight
build weight
Which line is considered to be the artistic pattern or length guide while sculpting hair?
crest line
design line
elevation line
design line
A stationary design line is a guide to where all lengths are directed
stable
moveable
texturized
stable
A weight area in a graduated form could be described as a:
natural projection
section of the head
concentration of lengths
concentration of lengths
A design line is used as a length guide for sculpting graduated, layered nd square combination form is referred to as:
stable
curved
mobile
mobile
Which of the following terms identifies the technique used to check the accuaracy of a hair design by using the opposite parting pattern?
parting
sectioning
cross-checking
cross-checking
Sculpting shorter lengths within the form to reduce bulk and create support and mobility is called:
outlining
texturizing
distrubution
texturizing
Texturizing reduces bulk without
lengthening the hair
adding volume to the hair
shortening the overall length apperance of the hair
shortening the overall length apperance of the hair
To maintain control of the hair, which of the following hair types should be texturized the greater distance from the scalp?
fine hair
blonde hair
coarse hair
coarse hair
As a general rude, coarse hair should be texturized at least
1/2 inch from the scalp
1 1/2 inch from the scalp
1 inch from the scalp
1 1/2 inch from the scalp
To allow for more control the shrinkage factor very curly hair should be texturized while it is:
dry
wet
damp
dry
A technique performed on the ends of the hair to reduce bulk allows for mobility softens the ends and blends weight lines is called
slithering
razor rotation
end texturizing
end texturizing
To perform a bevel under effect, teh blade is positioned behind the section of the hair and moved in:
long strokes
curved strokes
a side to side motion
curved strokes
The technique that creates irregular lengths for a chunkier effect is called:
slicing
etching
notching
notching
The technique used to position the shears parallel to the comb while moving both upward in unison is called:
slithering
bevel up
shear over comb
shear over comb
A sculpture technique that is commonly used to define the perimeter hairline such as the nape is known as:
outlining
texturizing
overcombing
outlining
To accomodate a growth pattern such as a widows peak, cowlick or whorl when sculpting the hair, which of the following statements wold apply?
allow additonal length in the growth pattern area
sculpt the hair in the growth pattern area shorter
perform heavy texturizing in the growth pattern area
allow additonal length in the growth pattern area
Which of the following growth patterns forms form a point at teh front hairline and curves to one side:
whorl
fringe
widow's peak
widow's peak
An uneven effect is created when sculpting hair that is:
completely wet
partly wet and partly dry
chemically treated
partly wet and partly dry
Infection control procedures include sweeping and disposing of cut hair:
prior to performing the air forming service
after performing blow dry service
prior to performing the air forming service
THIS SET IS OFTEN IN FOLDERS WITH...