Super Hornet Plane Captain Board
Terms in this set (277)
What manual will you refer to to find all general information on the aircraft such as dimensions, configurations, and aircraft specifications?
GAI-000 (General Aircraft information)
What manual will you consult to find the pre-deployment brief, what to wear on the flight deck, and general carrier fundamentals for aviation?
80T-105 (CV NATOPS)
What manual will you use to find the proper methods of detecting, treating, and preventing corrosion?
What manual will you use to find out about aircraft restraining devices?
What manual do you use to comply with a:
2. Turnaround Inspection
What manual are all emergency procedures located in?
LMM - 020
Where are the IRAC's located in the MRC-200?
In the very front under list of effective cards
A caution indicates what?
Danger to a system
A warning indicates what?
Danger to personnel
Damage is described as what?
Harmful force caused by an abnormal force or object (MRC-200)
Upon approach to the aircraft for a daily inspection, what state should the aircraft be in before performing an inspection?
Chocked, chained, and grounded.
What position should all switches be in?
NOASS - Normal, Off, Auto, Safety, Standby
What is the correct way to clean the polished chrome portion of the piston assembly?
Wipe from top to bottom with a lint free cloth and hydraulic fluid - then wipe clean with a lint free cloth.
How many differential pressure indicators are on the jet? and where are they located?
There are 17 Delta-P's on the Jet
1 in waveguide pressure desiccator
3 in MLG wheel well
2 in door 52 (APU door)
1 in 54L & 54R (AMAD door)
2 in door 65
2 in door 69L/R
What is the serviceable color of the waveguide desiccator?
What is the nomenclature for hydraulic fluid used on polished surfaces?
What are the tire pressures ashore & afloat?
Ashore: Nose = 150 psi +/- 5
Mains = 290 psi +/- 5
Afloat: Nose = 375 psi +/- 5
Mains = 350 psi +/- 5
What are the proper procedures for documenting a discrepancy found during a daily inspection?
1. Inform the parent work center
2. Initiate a MAF detailing discrepancy
3. Indicate on DTA on paper/ooma the MCN/JCN from the MAF in the corresponding block.
What door is the AMAD oil Delta-P in?
What door is the fuel filter Delta-P located in?
What is used to wipe the inlet Ice Detector Sensor?
A lint free cloth saturated with ethanol
What must be done before entering the cockpit?
Ensure seats and canopy jettison handles are pinned (4 pins total) and seats are in the up/safe position displaying white.
What is the minimum VDC acceptable for the battery?
When performing a daily inspection what do you wipe using a lint free cloth and hydraulic fluid?
The hydraulic pistons on all struts, drag brace, servo cylinders, actuating arms, and rollers.
What is the significance of panel 300?
it has an explosive charge and should never be stepped on. (Contains DFIRS - Deployable Flight Incident Recording System.)
How long are fuel samples valid?
How long is recommended after operation to obtain a fuel sample?
What PPE is required when performing fuel samples?
Rubber gloves, apron, & splash proof goggles
If the first fuel sample is contaminated what are the procedures following?
Drain 1 gallon into a bucket and take another sample - if that sample is also bad immediately notify Maintenance Control and bring both samples to QA
Who can check fuel samples?
1. Qualified aircrew
2. Shift supervisor
3. CDI/ CDQARs/QAR or QA Specialist
shall visually inspect all fuel samples for a clear and bright appearance
How many aircraft safety pins need to be pulled before flight?
10 for F-18 F/G 8 for F-18 E
What is the minimum required APU pressure for brake riding?
What is the minimum required pressure to start the APU with temperature above -15 degrees F?
What is the purpose of diving the ducts?
To ensure the engine is in a FOD free state
When cleaning the canopy and windscreen, what direction do you wipe?
Fore and Aft
What does MSP codes A30 represent?
Low Fire Bottle - *No personnel can go near the jet; inform shooter/radio
What is the oil capacity of the AMAD?
What is the oil capacity of the APU
How many static grounding points are there on the aircraft without pylons or tanks?
2 in each MLG
1 in NLG wheel well
1 in door 8
1 in tailhook point
1 in door 26
What would you do if you discovered the seat safe/arm handle in the armed position?
Stay next to the aircraft to prevent anyone from entering (never leave A/C unattended) Then find aircrew or qualified AME to safe the seat. [Notify someone with a radio]
* If you need to leave the aircraft, pull the circuit breaker for canopy, stow the boarding ladder, and put an 'X' in grease by the ladder
Where is the APU emergency shutdown switch located?
Nose wheel well
What must be done prior to opening the canopy?
Ground the aircraft & discharge the canopy with a static stick.
Where are the fuel shutoff valves located?
In the left and right main landing gear wheel wells.
What does the Nose Wheel Digital Display Indicator display?
What are the tiedown requirements?
Initial = 6
Permanent = 12
Heavy Weather = 18+
What are the 3 methods of opening the canopy?
electrically, mechanically, and forcibly.
What method is used to open the canopy forcibly?
A fire axe blow parallel and as near to the canopy as possible
If removing unconscious aircrew what must be done to ensure they do not suffocate?
The oxygen mask must be removed
What is the indication of a bad wheel brake assembly?
If a brake wear indicator is flush the multiple disc brake assembly must be replaced.
What is the indication of the axel over temperature indicator?
Flush = normal indication
Extended = over temperature condition
When checking an aircraft for hot brakes how should you approach?
fore or aft at a 45 degree angle
Can C02 be used to cool a wheel with hot brakes?
What can be used as a means of rapid cooling for hot brakes?
For a tire and wheel fire, can C02 be used?
Yes, as long as it is not directly applied to the wheel
What is the safe distance for an aircraft affected with a wheel fire?
What are the emergency procedures for an APU Fire/ APU Emergency Shutdown?
- Signal the pilot with large lazy 8's (pilot will discharge the fire bottle)
-Shut down APU - spool down 9-11 seconds
-If no shutdown, use APU Emergency Shutdown switch in NLG wheel well.
-If switch doesn't work after 11 sec, open 13L & 14L and pull the APU and APU Prime circuit breakers
-and wait 9-11 secounds
-open door 52 or 54L/
-Bounce co2 off the deck into the door
What are the emergency procedures for an AMAD Fire?
-Signal the pilot with large lazy 8's
- enter either left or right mlg wheel well and turn manual override arm clockwise to close position
repeat steps to prevent cross bleed
shut down engines
-Open door 54L/R
-Bounce Halon off the deck into the door
What are the emergency procedures for an External engine fire
Alert the pilot of perspective external engine fire
2. shut down perspective engine
3. enter the left or right main landing gear and disconnect electrical connector from engine fuel shutoff valve or cut electrical cable
4. turn manual override to close position repeat steps for the other main landing gear side to prevent cross bleed
5. if fire continues open doors 65L and 69L or R toward you not away form you
6. inject extinguishing agent into engine bay through open doors and vent opening door 68L or R
What are the emergency procedures for a tailpipe fire?
-Signal the pilot with large lazy 8's
-Shut down engine
-Windmill engine for 5 minutes
-Bounce Halon off intake wall into engine intake
What are the procedures for Engine Bay Fuel Leak?
-Signal the pilot
-Shut down the engine
-Disconnect cannon plug on fuel shutoff valve in MLG wheel well, and then close it.
-Call for troubleshooters
What design rim does the F-18 E/F have and why is it dangerous?
Split rim design, it is dangerous because if the rim splits during landing or inflation the rim will separate and shoot out outboard. Possibly shooting the rim at pressures of 375 + PSI
How far away must you stand from intakes at Idle and High Power?
Idle - 9ft High Power - 25ft
How far away must you stand from exhaust at Idle and High Power?
Idle - 115ft High Power - 925ft
What is the primary purpose of a plane captain?
Where is the MSDS located?
Ashore: Outside of maintenance control
Afloat: At Hazmat/Inside Corrosion 12C
Where are the danger areas of an F/A-18 Super Hornet?
Flight control surfaces, engine exhaust, APU exhausts, ATS exhausts, loaded ordnance, pitot/AOA probes, Tailhook, and Launch bar.
When are you allowed to walk under loaded ordinance?
What should be done before closing the canopy?
You should ensure the canopy sills and surrounding areas are clear from personnel and objects.
When should the aircraft seat pan oxygen level be checked?
After every flight
SCENARIO: While on an aircraft, you realize a tool is Missing/Broken, what do you do?
-Search immediate area (5 minutes max)
-Inform Maint Control and Flight Deck Control
-Inform QA and initiate a FOD search
-Write missing tool report and route
-Search Immediate area (5 minutes max)
-Inform Maint Control
-Inform QA and initiate a FOD search
-Write missing tool report and route
What is the oil capacity of the engine?
What is the maximum pressure allowed when fueling?
55 PSI (25 PSI with new foam in wings)
What size drive tool is used to open the canopy, and how many turns are required?
3/8 inch drive tool
112 +\- 1 externally
224 +\-2 internally
What do the MSP codes 982 & 983 indicate?
AMAD needs servicing
How long after shutdown do you have to service the engines?
What do MSP codes 980 & 981 represent?
Engine needs services
How do you treat an aircraft with a bulls eye
taxi the aircraft 300ft clear on both sides of personnel and equipment chock nose wheels shutdown engines and egress pilots hook up tow tractor and remove chocks taxi aircraft over emergency tire deflator
where are emergency tire deflators located
line division and airframes
what are the procedures if a pilot passes out in the cockpit
if the engines are online go into the main and shut off fuel drop the ladder and open the canopy if the canopy does not open use a C02 bottle to weaken the canopy transparency then use a fire ace to cut a hole in the canopy starting the cut parallel to the canopy frame ( to not hit the rocket motors)
List the steps in using a fire bottle
before use check gauge to insure the bottle is full stand bottle upright remove pin from handle push valve handle to the open position grab the nozzle and run the hose out aim nozzle and open nozzle handle to engage the hose
What do you do for a engine fire
Alert the pilot that he has an engine fire/AMAD fire by performing the proper hand signal shutdown the respective engine enter into the MLG well and disconnect connector from shutoff valve or cut electrical cable turn manual override arm clockwise to closed position enter other MLG and repeat
what do you do for amad fire in the bay
for fire in the amad bay open door 54L or R with the door toward you inject extinguishing agent into amad bay by bouncing the agent off the deck and into the bay
what do you do for fire in engine bay
open door 65L and R and 69 L or R inject extinguishing agent into engine bay through open doors by bouncing the agent off the deck and into the bay
what do you do for internal engine fire
Alert the pilot that he has an internal fire by performing the proper hand signal begin to windmill the respective engine for up to 5 minutes to extinguish the fire if the fire does not stop continue to windmill while injecting extinguishing agent into the intake
after the aircraft must be inspected for corrosion, engine must be removed for cleaning at i level
what do you do for a APU fire
Alert the pilot that he has an APU fire by performing the proper hand signal shutdown the APU the pilot will discharge the internal fire extinguisher in the event that the APU does not shutdown enter into the nose wheel well and set APU EMERGENCY SHUTDOWN SWITCH to Shutdown if apu emergency shutdown switch has no effect after 11 seconds open door 10L or 14L and pull apu breaker IF apu doesn't stop spray extinguisher into the apu exhaust
what is a missing or broken tool procedure
1. work center notify Maintenance control and searches work area
2.maintenance control notify the MO, AMO, MMCO, QA
3. upon notification of a missing tool flag the ADB to prevent release of aircraft
4 initiate a maf
5 MC forwards missing tool report to QA
6. if the tool is not found after the search the QA investigation shall sign a statement in the corrective action block of the MAF
7 QA officer will recommend what to do after investigation
8. if the tool is not recovered the mo shall release the aircraft after it is found that the tool is not in the equipment
what is your primary concern as a plane captain
safety of aircraft evolutions and personnel and equipment involved
where can you find the requirements to be a plane captain
4790.2B chapter 10 and 14
when you initaiate a MAF where do you put the MCN/JCN on the daily and turnaround
in the discrepancy block of the location the MAF pertains to
what when discovered codes do you use as a pc
J for daily and K for turnaround
what is the ADB and where is it located
aircraft discrepancy book located in maintance control
why is the adb important to you
the adb contains all mafs initiated to your aircraft you review your adb before launching your aircraft
what kinds of mafs are on the left of the adb and on the right
completed mafs are on the left and outstanding mafs are on the right
what is the a sheet
safe for flight
who signs the /141
qualified plane captain qualified safe for flight and the oncoming pilot
when do you look at the adb
before a launch daily turn maintenance and move
what are the three types of MAFS
up maf down maf and partially mission capable maf
what indicates an up maf down maf and partially capable maf
the letter u for an up maf the letter d or a red mark for a down maf the letter p for a blue mark for partially missions capable maf
what is the control stamp? what is identified on a control stamp
the control stamp is applied to a publication to keep track of that publication the control stamp identifies the location of the publication
what is an irac what is it for
irac stands for interim rapid action change it is used when there is a change or update to a publication
how can you tell if a pub is for A/B C/D E/F/G
A/B= AC C/D= AE E/F/G=EA
what publication contains aircraft fastener integrity
what publication contains emergency procedures
what does LOX stand for
liquid oxygen converter
what does obogs stand for
On board oxygen generating system
what door is the LOX/OBOGS in
what are the minmum lox liters on a legacy for a turnaround
what are the munimum lox liters on a legacy for a daily
how do you check the lox liters
check the lox gauge left hand side rear of the seat
what makes lox volatile
flammable or combustable materials such as wood cloth oil and gasoline
what aircraft lots have lox
lot 12 and below
where can you find the proper hand signals that a pc uses
what is the publication for fuel samplings procedures
what steps do you take if a fuel sample is bad
retain the bad sample drain 1 gallon and take another sample if the sample is good continue fuel sampling if the sample is bad notify maintenance control and give both samples to QA for inspection
who can sign for fuel samples
a qualified aircrew shift supervisor CDI CDQAR or QAR
what desiccants do you check during a daily inspection
HUD desiccant and waveguide desiccant
what are you looking for on a desiccant
what are the tire pressure requirements
legacy- NLG-150 MLG-250
what position does the hook go on the pad eye when chaing the jet
hook facing up
can you launch a jet knowing the daily will be dead before it lands
can you launch a jet knowing the fuel samples will be dead before it lands
when temp is below freezing how long do you wait to install intake exhaust covers why
two hours to prevent condensation from forming and freezing in the engine
what is mil-spec for hydraulic fluid
what is the mil-spec for oil
can a daily be completed on a jet that has maintenance being done to it
yes as long as the mcn/jcn is documented in the blocks of the daily that the maintenance is being working on
who signs safe for flight during hot seat
the off going pilot signs safe for flight
what is the proper ppe for fueling
crainial, goggles long sleeves gloves boots
what safety equipment is required for fueling operations
grounding strap chocks fire bottle watch fuel truck grounded
what is the minimum psi for checking
what is maximum fuel pressure for fueling
what is the maximum fuel pressure for a jet with new foam in the wings
can you fuel a jet with electrical power
yes as long as the power cord remains connected
how do you fuel only internals with external drop tanks installed
while fueling leave external pre checks out
how do you pre check a drop tank during a how refueling evolution
use external pre check switch in fuel door 8
can you operate the canopy halfway position
no either all the way up or down
how many saftet pins are on a single seat aircraft
8 for single 10 for dual seat
do you leave the pins in or out when you solo a dual aircraft
what are the 3 positions for the aft cockput canopy ejection handle
normal solo aft initiate
what should all switches in the cockpit be set to
normal off auto safe and standby
what are the three positions of the wing fold handle
spread hold fold
how can you tell if a seat is armed who can de arm a seat
the safe/arm handle is the armed positon ames or the pilot can de arm the seat
who is in charge of the aircraft during the move
how many ways are there to move an aircraft
4 push from NLG pull from NLG push/pull MLG
how many people does it take for a move
6, 7 if to the hangar Maintenance controller or QA
how fast can you tow a aircraft
5MPH or as fast as the slowest walker
do you need to have wing fold puns removed to manually fold wings
what should you do before you move an aircraft
stress panels installed, downloaded and dearmed lox is not installed check ADB
when the move is completed what must be done
aircraft must be securred chocks grounded strap chain ladder stowed and canopy down
when do you do a profile A/ FUll aircraft check
acceptance, down for 30 days, if no fcf A within past year, anytime requested by the mo
when do you do a profile B/ engines (only for legacy)
dual engine removal, dual eca, dual main fuel control change , installation of any unknown engine, anytime requested by the CO
when do you do a profile C/ flight controls
anyitme a flight control surface is re-rigged, installation of any flight control servo-cylinder or hydraulic drive unit, requested by CO
When do you do a profile D/ rear cockpit (trainer configuration only)
rear cockpit, acceptance of a newly assigned aircraft or upon recipt of an aircraft retuned from SDLM, reconfigured from missionized trainer configuration
when do you do a profile e/ emergency landing gear extension
at the descretion of the MO
what tools do you bring to duct dive
flashlight and teflon rod
What reference contains the responsibilities and requirements for the tool control program?
4790.2C CH 10. 12
who is the tool program manager
what is the primary purpose of the Tool control program?
to eliminate fod to aircraft and equipment caused by misplace tools
what marking must be etched on every tool item
organizational code of command, work center, and number of container the tool belongs to
who is authorized to sign tools for beginning of shift end of shift and tools being checked out in the tool log
collateral duty inspector, work center supervisor
Ad a plane captain when do you ataf your tools
upon checking out tools arriving to your work area in the middle of your work evolution at the end of your work evolution and when signing tools back into tool log
when a tool is turned in for worn or broken and is not replaced on scence what sheet must get updated to ensure tool accountability
What does ADB stand for
aircraft Discrepancy book
where can you find the ADB
Maintenance control and ooma
how do you navigate to the adb through ooma
click on the maintenance tab right click the aircraft modex and click on the adb tab
what does adb contain
most current daily/turnaround last 10 a sheets f sheets any outstanding mafs and oil consumptions
why is the adb important to the plane captain
the plane captains must review all outstanding mafs and discrepancies to the aircraft and ensure all discrepancies inputted have been recently verified and are within limits
what are the three types of mafs
up, down, partial
who signs the a sheet
qualified plane captain, qualified safe for flight personnel, aircrew
who signs for safe for flight during hot seat
the off going pilot
when you have outstanding mafs in the adb where do you go in ooma to verify the status of the maf and if the aircraft is safe for flight
you would go to the maf in ooma and review the in process for that maf
when initating a maf where do you put the mcn/jcn on a daily/ turnaround
in the discrepancy block of the location the maf contains to
what do you do for brake fire
1. Alert pilot of brake fire
2. clear the aircraft of all personnel and equipment for atleast 300ft
3. approach near fire only from front to rear of tire and extinguish with fire extingusher application from a distance and move nearer until effective
4. shutdown engines and egress pilot
5. inspect aircraft for contamination/corrosion
what is the corrosion manual
what do you do for brake failure
shut down engine 1 pilot can operate nose wheel steering while engine 2 is on
2. taxi pilot in a circle while throwing chocks at the nose to slow down jet
3. once aircraft comes to complete stop chalk mlg and shutdown engine 2
4. egress pilot and get tow tractor and move crew to move aircraft
what do you do for a bullseye
1. park aircraft clear of personnel and equipment
2. allow tire to cool ambient temperatures before approaching
3. a qualified airframes person will then bring the emergency tire deflator located in work centers 310 and 120 lay infront of the discrepant tire
4. tow the aircraft over the tire emergency deflator to puncture the tire and relieve pressure ensure all personnel and equipment is clear of area when deflating tire to avoid injury from possible wheel explosion
where do you find the requirements and responsibilities to become a plane captain
4790.2C CH 10.14
why was the plane captain program established
to incorporate training and qualify personnel to perform plane captain duties
who is the plane captain program monitor
who is the plane captain program manager
who overall designates the qualification as a plane captain in writing
commanding officer/ OIC
as a qualified plane captain when are you required to perform a monitor proficiency
semi annually, or every six months
where do you find the list of qualified plane captains and the monitor due date
maintenance monthly plan ENC 10
what is the primary duty as a plane captain
overall safety of aircraft evolutions and the personnel equipment involved
what cleaning compound is used to clean canopy when temperature is above 32 degrees fahernhiet
distilled water in a spray bottle
when temperature is below 32 degrees what is used to clean the canopy
no more than 50/50 isopropyl alcohol and distilled water in a spray bottle
what is the proper hand wipe techinque for cleaning the canopy
use short fore and aft strokes while wiping surface of canopy windshield throughly
what are the tie down requirement for initial intermediate permeant and heavy weather
how many tie down points are there
2- nose landing gear
3- forward fusalage
4 and 5- outboard of MLG
6-8 - inboard side of MLG
7 and 9- inboard side of the MLG
10 and 11- wings
12- aft fuselage
13 14- if center line is installed
what is the proper hook placement when hooking to a pad eye
inside pad eye hook will face away from jet pointed up
attached to aircraft will face down toward aircraft
when do you as a plane captain close and open circuit breakers
circuit breakers are pushed and pulled prior to aircraft start up and shut down
what panels are the circuit breakers located in
10R/L 13L 14 L
can you operate the canopy in the halfway position
no canopy is either fully up or fully down
how many safety pins are in a single seat/ dual seat
8 pins for single and 10 pins plus 1 solo pin for dual
where are the solo blocks located
what are the three positions of the aft cockpit canopy ejection handle
normal, solo, aft initiate
what is the correct sequence for pulling pins in cockpit and installing pins in cockpit
when pulling pins pull seat pin first then canopy when going installing pins canopy pin than seat
what are the three position of the wing fold handle
spread, hold, fold
what is the proper apu psi when temperature us under -15 degrees f and what is the apu psi when temperature is above -15 degrees f
2900 apu psi for temperatures below -15 f and 2500 apu psi for temperatures above -15 degrees f
When performing a daily on an aircraft what publication is used
How long is daily good for
72 hours or after 3 flight
how long does a daily take to accomplish
how long must you wait prior to checking tire pressure?
2 hours after engine shutdown
what tool is used to check tire pressure
tire pressure gauge
what publication must you have with you at all times when performing a daily on an aircraft
when daily is complete, where do you go to sign your daily off for that aircraft?
log onto ooma right click the aircraft you performed your daily on then click on ADB and go to daily/turnaround tab
what is the proper PPE when taking fuel samples from an aircraft
face shield, splash proof goggles, apron, gloves, long sleeves and boots
how long must you wait prior to taking fuel samples from aircraft
2 hours after fueling aircraft
what are the proper steps when a bad sample of fuel is collected
retain the bad sample, and drain 1 gallon of fuel, if sample is good continue taking fuel samples, and if sample is bad notify maintenance control and bring both bad samples to quality assurance for further investigation
where is the fuel sample kit located
can you launch a jet knowing that fuel samples will be dead prior to landing
what publications are used for performing a turnaround
how long is a turnaround good for
how long must you wait prior to servicing engine oils
within 1 hour after shutdown
how long must you wait prior to servicing the AMAD
during the aircraft walk around the exterior of the aircraft must be inspected for?
damage, loose or missing fasteners, and security of access door/panels
what must all armament switches be set to?
Normal, off, Auto, safe, standby
how many personnel should be present when fueling a aircraft
3 personnel one person with the fueling hose one person in the cockpit, and one standing fire bottle watch
what is the proper ppe when fueling
cranial, goggles, long sleeves, gloves, boots
what must you verify prior to fueling aircraft
aircraft is chocked, grounded, all saftey pins installed, vent tank wet light is operational, external and internal fuel pre check are engaged, fuel truck is grounded to aircraft and dire bottle watch is present
what is the minimum psi for checking fuel
what is maximum fuel pressure for fueling
what is the maximum fuel pressure for a jet wiith new foam wings
can you fuel a jet with external power on
how do you fuel only internals with a drop tank installed
leave drop tank external pre check switch out
how do you precheck a drop tank during a hot refueling evolution
use external precheck switch in fuel door 8
what type of fuel is used on a F-18
Jp-5 for navy
where is fuel door located
what position should the nozzle be in when hooked to fueling door
what does lox stand for
what is the temperture that lox can reach
what type of area should lox be handled
in a well vented area
what makes lox combustable
organic matter or flammable substance such as oil grease gasoline
when lox is vaporized and warmed to ambient temperatures what is the ratio of lox gaseous oxygen
862 volume of gas oxygen to 1 volume of lox
what is the explosive pressure that can be created if evaporation and expansion takes place in a confined space
explosive pressure of 12,000 psi
what aircraft have lox for F/A-18A-D
lots 12 and below
what aircraft lots have obogs
13 and above
what is the purpose of obogs
to distribute oxygen to the crew station
when do you as a pc service the apu
never the mechs service the apu
what does seawars stand for where is it located
Sea water activated release system
shoulder straps in cockpit
what are the 8 rules about fasteners
no missing fasteners forward of the intake
no two in a row
no missing fasteners on the leading edge of the panel
no missing fasteners on a corner of the panel
no more than 10%
no missing fasteners on panel 300
no missing on turtleback
none missing for more than 200 hours
what is a special inspecting
14 day wash-job
what position should the anti skid switch be in for ashore and afloat
what three things are serviced with nitrogen
when folding the wings manually do you remove the pins
no, the pins are for electrical disconnect only
what does ietm stand for
interactive electronic technical manual
how can you tell if the amad oil, engine oil needs to be serviced
the sight gage will be silver
what are the procedures for engine/amad servicing
1, inspect oil filer delta p
2, remove caps from oil fill and overflow disconnects
3, connect preoiler to engine/amad
4, connect overfill bottle
5, reset flowmeter to 0
6, begin pumping prevailer slowly until steady stream observed into drain bottle
7 subtract amount of oil in overfill bottle from amount serviced with preoiler
8, ensure servicing numbers get recorded in ADB
hydraulic delta p is popped what are the procedures
notify AM CDI
do not rest delta p
what is 4 down/up
ram air scoop
what is door 1
what is door 6
gun bay door
what is door 3
gun drop door
what is door 9
external power hook, canopy and ladder switch
who signs block 12 on the daily card
how many seconds will the apu stay online after both engines have started
how long do you wait for the pre check to work
45 seconds max
what is the minimum battery voltage for applying external power
what is required for a pro A launch
support equipment manual
CV natops manual
aircraft refueling natops manual
what are indications of hot breakes
extremem heat, orange glowing, popped axle overtemperature indicator
What are the procedures for Hot brakes/wheels/tires?
(1) Approach wheel/tire only forward or aft of the tire
(2) Inspect wheel/tire for overheat indications
(3) if overheated, signal pilot and let FDC or a runner know
(4) Taxi aircraft onto the highpower area with the overheated wheel/tire facing the JBD
(5) Clear area of all personnel and equipment for at least 300 feet
(6) Chock the non overheated tire and make sure brakes are off
(7) portable fans will be used for cooling of hot brakes/wheels/tires
What are the procedures for Brakes/wheels/tires fire?
(1) signal pilot and let FDC or runner know
(2) FDC or runner will notify maintenance which will notify fire department
(3) Clear area of all personnel and equipment for at least 300 feet
(4) Approach wheel/tire only forward or aft of the tire with fire extinguisher
(5) Avoid sudden or excessive application of extinguisher agent by softly spraying from the deck up to the tire
what is the indications of apu fire
Fire coming out of the APU intake, exhaust, or APU door #52
internal engine fire indications
fire coming out of the exhaust
external engine fire indications
fire coming of engine bay, or amad bay doors
indications of loss of nose wheel steering
pilot will flash taxi light
procedures for loss of nws
get move team together and move aircraft to spot, pilot will break ride
indications of brake failure
everything that can come out will (tail hook, canopy, beer can speed breaks)
procedure for brake failure
taxi aircraft in circle , when it's slowed down enough throw chocks under the tires
How can you distinguish an internal fire from external and vice versa?
Internal=Smoke out of the exhaust/External=Paint bubbling
What are you supposed to do before starting a Daily Inspection?
Check the ADB to see known discrepancies
when are fuel samples required
before the first flight
What items are required for a Daily Inspection?
MRC 200, PC Tool Pouch, Tire Pressure Gauge, Fuel Sample Kit, Lint free with hydraulic fluid, nc10
What is the maximum wind speed allowed for opening the canopy?
what do you do if the psi indicator turns red during fueling
stop fueling immediately
YOU MIGHT ALSO LIKE...
Super Hornet Plane Captain Board
Basic Fire safety
Frontier Airlines Emergency Procedures
OTHER SETS BY THIS CREATOR
Mock navy wide advancement exam for aviation ordnance