How can we help?

You can also find more resources in our Help Center.

92 terms

CDC's

STUDY
PLAY
What drives the rear wheels on the MJ-1B?
Hydrostatic Drive
Changing the position of the MJ-B1 accelerator pedal
varies the flow rate of the pump in the hydrostatic drive.
What is supported by the lift arms and used to hold the munition or store to be loaded?
Cradle Assembly
What aircraft loading missions are supported by the MJ-40?
B-1, B-2
What ensures the boom cannot fall if a hydrostatic line on the MJ-40 ruptures?
Hydraulic locking valve
Which loading controls are found only on the MJ-40 remote?
Ram up/down
What type of fuel is the MHU-83 capable of using?
Diesel or JP-8
What device controls the engine speed of an MHU-83?
Hand Throttle
Where are the controls located for adjusting the side frame width of the MHU-83?
The operator's position only
What device ensures the boom cannot fall in the event hydraulic power is lost or a component fails or a line breaks on the MHU-83 series lift trucks?
Counterbalance valve
The MHU-83 component used to lift the front wheels off the ground to allow side frame width adjustment is the
lift boom
What is the primary purpose of the hydraulic hand pump located on the right hand side of the MHU-83 lift truck?
Operating the hydraulic system should the engine quit during loading operations
What is the lift capacity of an MHU-83 with aluminum rollers installed?
7,000 pounds
Which bomb support rollers may be used with roller extensions?
All rollers
How many load binders do you need when loading with an MHU-83?
2
What type of stand is used to support triple ejector racks (TER) when loading them and storing them for future use?
Gantry stand
What type of load binder is attached to bomb support beams?
Nylon
Extension lift arms installed on the MJ-1 lift truck limits lifting capacity to
2,200 pounds
You install the extension lift arms on the MJ-1A/B lift truck by
inserting the ends of the arms into slots in the lift arms.
What is the MJ-40 and MHU-83 series lift truck weight limit reduced to when using the fork adapter assembly?
6,000 pounds
What accessory is used in conjunction with the MHU-83 series lift truck to load external heavy stores on a B-52?
fork adapter assembly
What attaches the fork adapters to the MHU-83 series lift truck's table assembly?
Two quick-release pins
What is the maximum lifting height when the adapter assembly is inverted on the MHU-83 series lift truck?
107.5 inches
Pylons are attached to pylon handling adapters for mounting or removing from aircraft with
the pylons bomb rack hooks
What bomb loading adapter is used in loading internal and external stores on the B-52?
F310707-500 bomb loading adapter
Which lift truck supports the use of the mechanical ram assembly (MRA)?
HUU-83 D/E or MJ-40
Where does the mechanical ram assembly (MRA) recieve its power from?
Through two hydraulic service lines attached to the lift trucks lift boom.
How is the mechanical ram assembly (MRA) primarily controlled/operated?
The lift trucks remote control unit.
What is the fully extended height of the mechanical ram assembly (MRA)?
83 inches
What accessory do you normally see attached to a MHU-141/M trailer with a mixed load of missiles?
M-9 adapter
What is the maximum load capacity of an MHU-110/M trailer?
15,000 pounds
How many main rail assemblies can be installed on the deck of the MHU-110/M trailer?
4
How many trolleys and chocks can the MHU-110/M trailer be configured with for round-shaped stores?
24 trolleys and 48 chocks
What is the maximum conventional munitions load capacity of an MHU-226/M trailer?
12,000 pounds
How many hinged deck panels are incorporated in the MHU-226/M munitions handling trailer design?
3
how many hinged deck panels are incorporated in the MHU-141/M munitions handling trailer design?
1
What component of the munitions handling trailer breaking system is connected to the tow vehicle to activate the trailer's breaking systemif the trailer becomes disconnected from the tow vehicle?
the breakaway cable
How many hand brake levers are located on the MHU-226/M munitions handling trailer?
2
What is the lift capacity of the MHU-204/M and MHU-196/M trailers?
40,000 pounds
how many different operational modes are available on the portable control unit (PCU) that controls the MHU-204/M and the MHU-196/M trailers?
15
To prevent personnel injury or equipment damage, each operational mode of the MHU-204/M and the MHU-196/M trailers automatically shuts off when either one of the two team members press a remote stop switch or when the
"deadman" switch is released on the PCU
How many people are required to remove the tow bar of the MHU-204/M and MHU-196/M trailers?
2
What MHU-204/M and MHU-196/M trailer component allow for precise lateral and longitudinal positioning corrections to lift trailers and load during lifting operations?
X-Y pads
Independent operation of either lift arm mechanism on the MHU-196/M trailer results in
rolling the load
What MHU-196/M trailer component supports the lift arms under transport conditions?
Retractable travel locks
What component(s) of the the MHU-196/M trailer accommodate(s) various load adapters?
A removable lift beam extention
How much air pressure must be in the compressor tank before loading with the MHU-196/M trailer?
90 psi
What is the ammunition capacity of the 20 mm linkless ammunition loading system (LALS)?
2,100 rounds
Which component of the linkless ammunition loading system (LALS) transfers rounds into the gun systems loading adapter?
Interface unit
What position must the shift lever handle on the interface unit be in before mating the linkless ammunition loading system (LALS) to the aircraft?
BYPASS
What is the ammunition capacity of the 20 mm universal ammunition loading system (UALS)?
2,100 rounds
What component of the A-10 ammunition loading system (ALS) interfaces with the aircraft during ammunition loads?
GFU-7E ALA
During normal loading of the A-10 gun system, where does the ammunition loading assembly (ALA) get its power?
The aircraft's hydraulic system
How many different outputs can an A/M 32A-60 provide?
3
Which item is the only auxiliary power unit (APU) to provide both electrical and pneumatic power?
A/M 32A-60
Which A/M 32A-60 control panel has the switches and controls necessary to operate the DC generator and to monitor the DC voltage output of the generator set?
DC instrument
The brake on the A/M32A-60 is released by
lowering the tow bar
Due to the expansion properties of fuel, an unmodified A/M32A-95 fuel tank should not be filled more than approximately
1/2 full
What electrical output is supplied by the A/M 32A-86 generator set?
115/200 VAC or 230/400 VAC
How many instrument/control panels must the operator make use of during operation of the A/M 32A-86 generator set?
3
Which panel of the A/M 32A-86 generator set has the circuit breaker to shut off current flow in case of an overload?
External AC
What type of power is provided to the MA-1 and MQ-9 aircraft by the starter cart assembly (SCA) for use in the avionics systems?
28 VDC
Where is the control panel of the starter cart assembly (SCA) located?
Underneath a cover located at the top of the unit
Fighter aircraft may be exempt from 50-foot distance placement requirements of an auxiliary power unit (APU) during
combat or simulated combat operations
What area must you avoid when operating units powered by turbine engines?
The engine plane of rotation
How much air pressure is produced by the MC-2A?
15 cfm at 200 psi
What is the maximum air pressure you may use for cleaning?
30 psi
What Air Force Occupational Safety and Health (AFOSH) standard identifies the protective equipment used with compressed air?
91-501
Before you connect or disconnect a high-pressure service hose, you must make sure the system is
not pressurized
What power output of the portable floodlight sets is used for powering common electrically powered hand tools?
115-120 VAC
The FL-1D can serve as a ground power source for MQ-1 and MQ-9 aircraft when used in conjunction with a/an
DCs40-75 "Sorensen" power supply unit
In what position must the FL-1D's floodlight platform be during towing?
Lowered completely
What additional piece of aerospace ground equipment (AGE) is required during operation of the A/M 32C-10 air conditioner?
A/M 32A-60 generator set
Where are the A/M 32C-10 duct hoses stored?
in the rear storage compartment
What is the maximum amount of bleed-air pressure that may be applied to the -10 air conditioner?
45 psi
What additional piece of aerospace ground equipment (AGE) is required during operation of the polyalphaolefin (PAO)/ air cooling cart?
None, its a self contained system
How many fluid temperature modes are available on the polyalphaolefin (PAO)/ air cooling cart?
2
What must be done before making or breaking a connection between the polyalphaolefin (PAO)/ air cooling cart and the aircraft?
Ensure the system is depressurized
Where is the cool-air hatch on the MJ-2A hydraulic test stand?
top of the unit
What is the primary reason for making sure the aircraft fittings are clean before attaching hydraulic servicing hoses?
Dirty fittings can introduce contaminants to the hydraulic systems causing damage to valves and lines.
Which aircraft require aircraft armament system personnel to use the self generating nitrogen servicing cart (SGNSC)?
F-22 only
What precaution must be taken prior to attempting to loosen fittings, or remove tubes or hoses when using the self generating nitrogen servicing cart (SGNSC)?
You must vent the pressure from that part of the system through the appropriate valve.
What is the height range of the B-1 maintenance stand?
3 to 10 feet
What is the maximum static load the B-1 maintenance stand can sustain?
500 pounds
What is the platform height range of the b-4 maintenance stand?
3 to 7 feet
The hand pump for raising the B-4 maintenance stand is located on the
platform near the ladder
What is the platform height range of the B-5 maintenance stand?
7 to 12 feet
What maintenance stand is a nonadjustable 4-foot platform with wheels on the back legs?
C-1
If the split-deck maintenance platform's tape switches detect an obstruction during operation, they stop the unit's
forward drive, platform extension, and lowering capabilities.
What is the total load of the split-deck maintenance platform?
2,000 pounds
During an operator's pre-use inspection of aerospace ground equipment (AGE), what is required to ensure proper unit operation?
cycle the unit completely through its range of capabilities
Where must you annotate any defect you find on aerospace ground equipment (AGE)?
AFTO Forms 244 and 245