NOCTI ENGINEERING PT2
Terms in this set (33)
Which of the following indicators is used to denote the center of a circle?
What is the third color band on a resistor represents?
The first and second band represent the numerical value of the resistor, and the color of the third band specify the power-of-ten multiplier. The fourth represents the tolerance. The color bands are always read from left to right starting with the side that has a band closer to the edge.
Identifying leader in the assembly process in order to routinely compare one's processes and outputs to the leader is called
When energized a solenoid actuates upon which of the following objects:
Which statement best describes precision alignment?
It corrects any defects in the shaft
The most important factor for an engineer in selecting a project solution should be
Healthier staff, increased attendance and productivity, increased morale, and reduced litigation risks are some of the advantages of adhering to what regulations?
An international body of technical standards for various industries, designed to promote international trade, engineering conformance, and most recently environmental awareness is known of
International organizations for standardization
When determining the degree of acceptable risk in a project, an engineer should always consider
A cost/ risk / benefit analysis
Training and _____ may be given to comply with OSHA in the workplace
A good method of maintain a safe work area is to maintain a clean work bench, attend safety meetings and
Abide by safety signs
Performing engineering functions, ethical conduct is the responsibility of the
Immediately report the malfunction of any piece of equipment
The _________ code defines requirements when joining metals using the MIG process
Since 1971, when _____ was created, occupational deaths have been cut by 62 percent and injuries have declined by 42 percent
When a gas cylinder is at work station , as safety precaution,
At least two inches off flow
Because switches can fail after opening a disconnect, safest practice is to
Lock and dag the disconnect
For the sake of maintaining good safety practices, never use an ohmmeter on a circuit that might be
When testing with compressed air, caution should be given to the _____________ used.
Pounds per square inch of a gauge
Install surge protection on electrical equipment to
Shield equipment from sudden power increases.
A _______switch opens when current exceeds predetermined safety level.
What is the name for the international body of technical standard for various industries, designed to promote international trade, engineering conformance and environmental awareness?
International Organization for Standardization
Which of the following drawing methods is used to generate a 2D Multiview drawing
Which of the following drawing methods generates a pictorial drawing?
This process may use techniques including constructive solid geometry, implicit surfaces, subdivision surfaces to shape individual objects, and placement of various spots on more xyz grids that are mapped out. Changing one or more variables might result in updating related graphics. This process is known as
Of the following, Which lines indicate a hidden edge
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
What is an oblique, isometric perspective orthographic drawing method? Which one will generate a 2D Multiview drawing?
Oblique: type of technical drawing of graphical projection used for producing two-dimensional images of three-dimensional objects. The objects are not in perspective, so they do not correspond to any view of an object that can be obtained in practice.
Isometric: a method for visually representing three-dimensional objects in two dimensions in technical and engineering drawings. It is an axonometric projection in which the three coordinate axes appear equally foreshortened and the angle between any two of them is 120 degrees.
An orthographic drawing represents a three-dimensional object using several two-dimensional views of the object. It is also known as an orthographic projection.
What is the meaning of OEM?
Original Equipment Manufacturing
Manufacturing product quality control includes
Production flow chart
The following process of converting raw materials to finished products is
Typical gas pressure gauges will read_______ at atmospheric pressures.
Undercutting is a condition that generally occurs when the
When the welding current is too high
A means of monitoring the assembly and fabrication process by gathering data and samples to evaluate variations in the process that may impact the final product is called
YOU MIGHT ALSO LIKE...
Academic Word Lists - AWL Sublists
End of Pathway Assessment-NOCTI
Design Part 2
Engineering 1 Study Guide
OTHER SETS BY THIS CREATOR
FCIQ FINAL REVIEW
FCIQ MIDTERM REVIEW
Quiz for FCSC NYIT
NOCTI ENGINEERING PT4
THIS SET IS OFTEN IN FOLDERS WITH...
NOCTI Pre Engineering Exam Study Guide
NOCTI Pre-Engineering Study Guide 2
NOCTI Pre-Engineering Study Guide 3