Upgrade to remove ads
CDC Volume 1
Terms in this set (100)
When does Air Force Occupational and Environmental Safety, Fire Protection, and Health (AFOSH) standards training end?
it never ends
Who must ensure that you are trained on the hazardous chemicals or materials which you are exposed to?
When a hazard reported on an AF Form 457, USAF Hazard Report, is corrected, the safety office investigator must report the corrective action to the originator within how many working days?
An AF Form 1118, Notice of Hazard, can be removed from a hazard...
after verification by the issuing authority that the identified hazard has been satisfactorily corrected
What Air Force publication establishes guidance for training employees on the health and physical hazards associated with, and proper preventive measures to be taken when using or handling hazardous chemicals in work centers?
AFI 90-821, Hazardous Communication
Material safety data sheets must be reconciled with the work center's hazardous chemical inventory?
What Air Force instruction establishes specific requirements for fire protection?
91-203, Air Force Consolidated Occupational Safety Instruction
Supervisors must ensure that fire extinguishers are inspected at a minimum of...
Which of the following lists the proper steps for using a fire extinguisher in the correct sequence?
pull the pin; aim nozzle at base of fire; squeeze the handle; sweep the nozzle back and fourth along the base of the fire (PASS)
Which control tower signal indicates that you should clear a runway or taxiway?
flashing red light
The maximum pounds per square inch (psi) of air pressure you should use to clean an ejection seat is...
What form will you use to document your subordinates' completed work area training?
AF Form 55, Employee Safety and Health Record
You will discuss mandatory Job Safety Training Outline items with your subordinates upon initial assignment prior to starting work or when...
work conditions or tasks change
The cardinal principle of explosive operations is to expose the minimum number of...
people to the minimum amount of explosives for the minimum amount of time
If you are responsible for establishing explosive operation personnel limits, which guideline should you consider?
supervisor, worker, and visitor limits must be clearly posted at each operation when explosives are present
Who should be notified each time your egress shop's fire symbols are changed?
base fire alarm communication center
Which is a special provision for storing explosives that applies only to egress shops?
net explosive weight (NEW) limitations do not apply for those components installed in egress seats not being worked
Serviceable and unserviceable egress explosive items must be...
An explosive facility license must be requested from...
the weapons safety office
Who determines the type, quantity, and locations of fire extinguishers for an explosive storage facility?
base fire chief
How do you determine the net explosive weight (NEW) for each explosive item listed on your AF Form 2047, Explosives Facility License?
multiply the minimum number of each item needed to accomplish the mission by the NEW
When renewing your shop's AF Form 2047, Explosives Facility License, you coordinate with your...
commander, weapon safety, fire department, and security forces
The daily explosive laden vehicle inspections include ensuring that...
the fuel tank and feed lines are secure and not leaking.
When can you load or unload explosives from a vehicle with the engine running?
when the engine is required to provide power to support equipment used in loading and unloading the vehicle
Who determines explosive movement routes?
weapons safety office
Local written explosive operation safety standards must contain explosive and personnel limits,
...operating locations, safety requirements, actions to be taken during emergencies, and step-by-step procedures
Who is responsible for instructing workers on the safety standards for the explosive operations they'll be performing?
When can an Airman confirm the presence or absence of nuclear weapons at any general or specific location?
What program is designed to select and maintain personnel whose conduct and behavior demonstrate the highest levels of integrity, reliability, trustworthiness and allegiance to the United States to perform duties associated with nuclear weapons?
personnel reliability program
A personnel reliability program (PRP) package must be completed within how many days of assignment or training notification?
When selected for personnel reliability program (PRP) duties, at what point does your evaluation stop?
never, you are continuously evaluated
No-lone zones are identified by...
each organization with a mission or function involving the nuclear mission.
The technical order catalog can be found on what website?
enhanced technical information management systems (ETIMS)
What type of technical order is a complete list of all technical orders for a specific weapons system or a piece of equipment?
list of applicable publications (LOAP)
Operation and maintenance (O&M) technical orders (TO) are written to provide...
operation and maintenance instructions including troubleshooting, calibration, and servicing
What operations and maintenance (O&M) technical order (TO) dictates the patterns for TO numbering?
00-5-18, AF Technical Order Numbering System
What type of operations and maintenance (O&M) technical order provides detailed procedures for equipment maintenance in a portable size intended to be used on the aircraft?
job guide (JG)
An immediate action time change technical order (TCTO) must be distributed to all affected personnel within how many hours of receipt?
What type of TCTO is issued when a deficiency could result in injury to personnel, damage to property, or unacceptable reductions in combat efficiency?
What type of TCTO is issued when material, mechanical, operational or tactical deficiencies occur which could result in conditions that reduce the operational life of equipment?
What types of TOs involve instructions relating to ground handling of air and space vehicles, general maintenance practices, management of precision measurement equipment, and the safe use of the Air Force equipment?
methods and procedures
Which methods and procedures TO assigns responsibilities for TO improvement reporting?
00-5-1, AF Technical Order System
Which methods and procedures TO provides step-by-step procedures for filling out aircraft and equipment forms?
00-20-1, Aerospace Equipment Maintenance Inspection, Documentation, Policy, and Procedures
Which methods and procedures TO explains the Integrated Maintenance Data System (IMDS)?
00-20-2, Maintenance Data Documentation
What types of abbreviated TOs provide guidance, including applicable safety warnings, cautions and notes, and specific accept or reject criteria for performing an inspection?
inspection work cards
What types of abbreviated TOs are most often used by a phase dock chief to control the assignment of work during an inspection?
inspection sequence charts
What types of abbreviated TOs guide the tasks or operations in the sequence deemed the most practical to determine operational readiness of equipment and minimum serviceable condition?
What types of abbreviated TOs may be published when two or more differing specialty skills are involved in accomplishing a task?
Once a preliminary TO has been sufficiently verified to make it usable for operation and maintenance, it's printed as a...
What type of TOs cover time compliance TS, safety supplements to technical manuals, and operational supplements to technical manuals?
are just as binding as a formal TO
What TO category covers aircraft furnishings and recovery equipment?
What TO category would you find storage procedures for rocket catapults?
Where would you go to find a specific TO for a part when you have the part number?
the "TO/Equip XREF" page in ETIMS
What automated TO management application do TO managers use to perform all TO distribution office operations except the receipt and redistribution of TOs to multiple subaccounts?
joint computer-aided acquisition logistics support system (JCALS)
What automated TO management application is used to submit recommended changes to TOs?
joint computer-aided acquisition logistics support system (JCALS)
If a recommended technical order change is approved, it is included in the technical order...
within 365 calendar days
in order to receive a monetary award, you must submit your recommended TO change to the Innovative Development through Employee Awareness (IDEA) Program within how many days of the date of notification for recommended change approval?
90 working days
If you submit an idea to the Innovative Development through Employee Awareness (IDEA) Program within your job responsibility and the results are intangible, how much money will you receive?
you will not receive money, but may receive a non-monetary award
What type of pliers has a pair of croppers located above the pivot in order to shear larger wire?
lineman's side cutting
The size of a socket wrench is expressed by the size of the drive or by the size of the...
fastener it's designed for
What is the proper use of a hand tool?
if a file is designed to be used with a handle, never use the file without the handle. Holding the sharp tang in your hand while filing can cause serious injury
Who is responsible for the Tool and Equipment Management Program?
maintenance group commander
All composite tool kits are accounted for at the beginning...
and end of each shift by both outgoing and incoming personnel
Authorization to clear red Xs when a tool cannot be located is limited to no lower than the...
Your TO specifies a measurement requirement and you decide to use a ruler for the measurement. However, your ruler measures in fractions and the measurement is in decimal. How would you convert the fraction 3/4 to decimals?
divide 3 by 4
When performing a shell receptacle test with a multimeter on an Advanced Concept Ejection Seat (ACES), the resistance between the connector shell and the receptacle must be...
0.010 ohms or less; excluding lead resistance
The TTU-415/E Tester is used to perform...
a velocity sensor test
What sequences the F-22 escape system, including the canopy thruster, inertia reel gas generator, electronic explosive device, canopy rocket, seat catapult and the central integrated processor guillotine?
emergency escape sequencer
Which of the following is a common cause of sling mishaps?
personnel walking under suspended loads
The F-16 canopy sling must be replaced if there are more than...
six broken wires in any 1 inch length of cable
When installing a canopy onto an F-16, before you perform maintenance required to mate the canopy to the airframe, you lower the canopy approximately how many degrees in relation to the longeron?
Which item is a component of a crane?
Which step will reduce hazards when operating a crane?
using outriggers when operating on a surface that is not level
What is the maximum platform load for a B-1 maintenance stand?
After performing a prior-to-use inspection on a B-1 maintenance stand, what is the first step in raising the stand?
place the maintenance platform in desired position and ensure that caster locks are engaged and wheel brakes are locked
What must engage once a B-4A maintenance stand's platform has attained the desired height?
safety lock pins
What controls the rate of descent when lowering the B-4A maintenance stand's platform?
Which aerospace ground equipment (AGE) power unit consists of a gas turbine engine, aircraft type AC generator, generator voltage regulator, rectification system for DC power supply, engine fuel system, batteries and engine electrical system for starting and control functions and is used mostly on fighter and attack aircraft?
Which generator set is replacing the "Hobart" because it has a diesel engine which runs cleaner and is safer for the environment?
Which power unit is wall mounted and has a 3-phase output rating of 100KW?
Power units should never be positioned within what distance of an aircraft fuel system vent?
Which flood light set includes two receptacles for 240V and three receptacles for 120V?
Which statement best describes proper procedures regarding flood light sets?
never climb into a flood light's compartment to keep warm
What type of bolt is used where shearing, or sidewise stress occurs?
When visually inspecting ballistic tubes and ballistic tube assemblies for damage, inspect for chafing, galling, and...
Locally manufactured hose must be tested to how many pounds per square inch (psi)?
What size of fitting will you use when the outside diameter of the tubing is 1/4 inch?
Which item is classified as a metal foreign object?
Who is responsible for ensuring an effective foreign object damage (FOD) prevention program is established?
vice wing commander
When should you inventory all of the tools you brought to a job site, including TOs, bench stock, and special tools?
before and after each job
If you've exhausted every effort to find a dropped piece of small safety wire in a cockpit, including using a borescope, the next step is to...
place a detailed entry in the aircraft forms
Empty FOD bags after each job and...
never place the bag in a position where the contents may be spilled into the cockpit
Which type of corrosion is an advanced form of intergranular corrosion that "lifts up" the surface grains of a metal?
Which degree of corrosion may include blisters or scaling and flaking of the coating or paint, with pitting depths as deep as 0.010 inch?
What type of brush would you use to remove corrosion from an aluminum surface?
What term is defined as the flow of electrons through a conductor?
What term is defined as the opposition to current flow in an electrical circuit?
For the free electrons in a material to move, there must be a difference in the potential between two points. That difference is that one point must have an excess of...
electrons; the second point must have a lack of electrons
What is a common manifestation of static electricity that may be dangerous outside an egress shop?
THIS SET IS OFTEN IN FOLDERS WITH...
CDC Volume 2
CDC Vol. 3
CDC Vol. 4
YOU MIGHT ALSO LIKE...
NAMP chapter 10
BUMEDINST 5100.14, Headquarters Navy Occupational…
POL CDC URE VOL 1
MIL code 5