Upgrade to remove ads
Module 3 All terms and questions
Terms in this set (42)
A tool that consists of a glass tube in a sleeve with hooks on each end is called a __________.
Which type of square can be used to check only right angles?
A large hand plane used for rough work is the _______.
After using a grinding wheel to sharpen a plane iron, the edge must be dressed using a(n) ________.
The clamp whose jaws can be adjusted independently of one another is the ________.
The handsaw that would be used to make a scroll cut on a trim piece is the _______.
The saw blade should be held at about a 60-degree angle to the wood when cutting with a ________.
Before performing maintenance or changing accessories on any power tool, be sure that it is _____________.
A small extension cord can be used for any type of power tool/
report the problem to your supervisor or instructor
If a power tool is making unusual noises, sounds, or vibrations, _______.
Which of the following operations is not typically done with a portable table saw?
When ripping stock with a portable table saw, the blade should not project above the material being cut by more than _________.
remove the chuck key
Before starting a drill press, always _________.
A laminate trimmer is a specialized type of _________.
A pneumatic nailer or stapler is powered by ______.
One of the hazards associated with a table saw is the possibility of ________ as the stock gets pinched as it travels through the saw blade.
The ______ should be sharpened on a bench grinder to ensure smooth cutting.
When cutting trim molding around a door frame, you would most likely be performing _________.
If a long board has an imperfect edge, a jointer plane can be used to make it ________.
Mortise and tennon joints
________ are formed when the tongue of a workpiece is fit into a rectangular cutout or opening on an adjoining piece.
Use a(n) ________ to hold a door safely on edge when planing it.
A cut that is made across the sloping edge or side of a workpiece at an angle of less than 90 degrees is known as a(n) ________.
Pocket (plunge) cuts
The installation of a strike plate and hinges in a door jamb would require ________.
When measuring, account for the amount of material removed by the saw blade, which is known as the ________.
A(n) __________ is a triangular joint often used to attach drawer fronts to the sides in antique furniture.
A cut made across the grain in lumber is known as a(n) __________.
A rectangular cut made along the edge or end of a board to receive another board is known as a(n) ___________.
A(n) _________ can be used to cut lumber at precise angles.
The installation of crown molding often requires that wood be cut with both a bevel and a miter, which is known as a(n) __________.
For a cabinet drawers, ___________ should be cut in the sides, front, and back to receive the drawer bottom.
A power tool should be disconnected before performing maintenance on it.
diameter of the largest blade that can be used
The size of a circular saw is determined by the _________.
The maximum size of stock that a drill press can accept is a determined by the _______.
When routing plastic laminates and plywood, it is recommended that you use a(n) __________.
When cutting bevels or chamfers with a jointer plane, use a(n) ______.
Which of the following materials should not be cut with power metal shears?
Pneumatic nailers and staplers are powered by _________.
The tool that includes an internal compensator mechanism, which allows for rapid setup time is the ________.
Which of the following tools is specially useful when laying out angle cuts for roof rafters?
The type of plane used to smooth rough lumber is the _________.
Which of the following clamps might be used when assembling in irregular-shaped object such as an octagonal table?
The type of saw commonly used with a miter box is the __________.
THIS SET IS OFTEN IN FOLDERS WITH...
Module 1 Construction Safety
exterior finishing review questions
Module 4: Construction Drawings, Specs &…
Module Two: Building Materials, Fastener…
OTHER SETS BY THIS CREATOR
Carp 2 Module 6 Doors review questions
NCCER Module 1 Basic Safety Trade Terms
Module 16_ Cabinet installation trade terms
Carp 2 - Mod 2 - Cold formed