QUESTION that i got wrong
Terms in this set (51)
Which two features of enterprise class equipment assists an enterprise network in maintaining 99.999 percent up-time? (Choose two.)
redundant power supplies
Which two requirements must always be met to use in-band management to configure a network device? (Choose two.)
at least one network interface that is connected and operational
Telnet, SSH, or HTTP access to the device
What is a characteristic of in-band device management?
it is used to monitor and make configuration changes to a network device over a network connection.
How can an enterprise network be designed to optimize bandwidth?
by organizing the network to control traffic patterns
In which situation would a network administrator install a Cisco Nexus Series or Cisco Catalyst 6500 Series switch to promote infrastructure scalability?
on a data center network to provide expansion and transport flexibility
What is an advantage of PVST+
PVST+ optimizes performance on the network through load sharing.
To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display?
The role of the ports in all VLANs.
The root bridge BID.
Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?
Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)
redundant links between Layer 2 switches
removing single points of failure with multiple Layer 2 switches
If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?
lowest MAC address
What is the purpose of HSRP?
It provides a continuous network connection when a router fails.
n which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)
Which port state will switch ports immediately transition to when configured for PortFast?
Which three components are combined to form a bridge ID?
extended system ID
A network administrator is preparing the implementation of Rapid PVST+ on a production network. How are the Rapid PVST+ link types determined on the switch interfaces?
Link types are determined automatically.
Which two types of spanning tree protocols can cause suboptimal traffic flows because they assume only one spanning-tree instance for the entire bridged network? (Choose two.)
What additional information is contained in the 12-bit extended system ID of a BPDU?
What is a characteristic of a Layer 2 loop?
Broadcast frames are forwarded back to the sending switch.
Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?
When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form the bundled channel only if the port receives PAgP packets from another device?
Which PAgP mode combination will establish an EtherChannel?
switch 1 set to desirable; switch 2 set to desirable.
When a range of ports is being configured for EtherChannel, which mode will configure LACP so that it initiates the EtherChannel negotiation?
Which two load balancing methods can be implemented with EtherChannel technology? (Choose two.)
source MAC to destination MAC
source IP to destination IP
Which two roles are typically performed by a wireless router that is used in a home or small business?
Which three Wi-Fi standards operate in the 2.4GHz range of frequencies? (Choose three.)
What is the purpose of the Distributed Coordination Function in an IEEE 802.11 WLAN environment?
It allows a client to detect whether or not a channel is clear prior to transmission.
During which stage of establishing connectivity between a WLAN client and an AP does the client learn the MAC address of the AP?
A student uses a laptop to upload an assignment to a file server. Which wireless frame type did the laptop send to locate and associate with the campus access point?
For which discovery mode will an AP generate the most traffic on a WLAN?
What is a difference between Cisco APs that operate in a home environment and Cisco APs that operate in a corporate environment?
Some corporate AP models can operate in either autonomous mode or controller-based mode.
Which statement defines the control frame operation between two stations?
After receiving a data frame, the receiving station will send an ACK frame to the sending station if no errors are found.
If three 802.11b access points need to be deployed in close proximity, which three frequency channels should be used? (Choose three.)
Which two commands will provide additional information about the state of router adjacencies, timer intervals, and the area ID? (Choose two.)
show ip ospf interface
show ip ospf neighbor
When OSPFv2 neighbors are establishing adjacencies, in which state do they elect a DR and BDR router?
Which two pieces of information are used by the OSPF MD5 algorithm to generate a signature? (Choose two.)
Why do OSPF serial interfaces usually require manual bandwidth configuration?
OSPF uses the bandwidth value to compute routes for its routing table.
Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?
show ip protocols
Which command can be used to verify the contents of the LSDB in an OSPF area?
show ip ospf database
An ABR in a multiarea OSPF network receives LSAs from its neighbor that identify the neighbor as an ASBR with learned external networks from the Internet. Which LSA type would the ABR send to other areas to identify the ASBR, so that internal traffic that is destined for the Internet will be sent through the ASBR?
Which two statements correctly describe OSPF type 3 LSAs?
Type 3 LSAs are used to update routes between OSPF areas.
Type 3 LSAs are generated without requiring a full SPF calculation.
Which EIGRP route would have the preferred administrative distance?
a summary route
Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
What is indicated when an EIGRP route is in the passive state?
The route is viable and can be used to forward traffic.
Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
What is the purpose of using protocol-dependent modules in EIGRP?
to accommodate routing of different network layer protocols
Where are EIGRP successor routes stored?
in the routing table and the topology table
In an EIGRP topology table, a route that is in an ________ state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.
Which three metric weights are set to zero by default when costs in EIGRP are being calculated?
Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
to exclude some interfaces from the EIGRP process
Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors?
the topology table
Which command can be issued on a router to verify that automatic summarization is enabled?
show ip protocols
YOU MIGHT ALSO LIKE...
Test Preparation TOEIC, SAT, TOEFL
CCNA 3 Final Exam
Allen CCNA 3 Study Cards
CCNA 200-125 Q
OTHER SETS BY THIS CREATOR
security part 3
security past exam 2
security past exam 1
THIS SET IS OFTEN IN FOLDERS WITH...
CCNA3 ch 2
ccna4 ch 1exam
CCNA 3 ch 3
ccna4 ch 3 exam